Low Voltage Swing Gate Operator designed for tubular steel, vinyl, wood, or ornamental gates for residential, farm and light commercial use. The PRO2500 is for single swing gates. Add the slave unit PRO2550 for a double swing gate (below).

• 12 volt system, no electrician needed for installation

• Gate will work during electrical power outage

• Quick and easy installation, with user friendly instructions

• Solar Panel Charger available for remote locations

• Will operate a gate up to 16' long and weighing up to 500 lbs. each leaf.

• Can operate 100 or more gate cycles per day using transformer charger, depending on gate size and weight

• Large control box with room for extra battery and accessories

• Receiver unit with antenna and 10' cable can be placed in best location for reception of signal

• Can be operated by remote transmitter, digital keypad, push button or combination

• Full systems capable "add on ready" heavy-duty control board includes adjustable obstruction sensing, gate sequencing and auto close settings (0-120 seconds).

• High cycle capability with true soft start and stop operation.

• Full access ready package includes battery, radio receiver, entry transmitter, AC transformer, and all necessary mounting hardware for a standard installation.

• Can operate as 'push to open' or 'pull to open' (specify when ordering - extra hardware required for push to open)

• UL rated for Class I, II, III & IV. System certified to be in compliance with UL 325, 4th edition.

• 18 month limited warranty applies to replacing parts from GTO, Inc.

Technical Specifications:

Drive

• Powered by reliable 12 volt DC motor, 64:1 planetary gear drive system.

• Temperature rating of motor: -5º F (-28º C) to +160ºF (+71ºC)

• Opening time is 20-24 seconds.

• Range of arm stroke is up to 22" (56 cm), with arm fully retracted is 40.25" (102 cm), mounting point to mounting point.f

Power

• The PRO-SW2500 system is powered by a 12 volt DC/7.0 amp hour, sealed, rechargeable battery.

• Optional second battery fits in control box, used for solar applications or high traffic applications, if needed

• Battery charge maintained by a 120V AC/60 Htz input at 40VA output, transformer rectified to 14 V DC through the GTO Control Board. NOTE: Transformer should never be connected directly to any battery.

• Optional GTO Solar Panel Charger: float voltage 14.5 V DC output from a 19-3/8" (49.21 cm) x 15-1/4" (38.74 cm) silicon alloy panel. Generates minimum of 10 watts at 600 mA. A gated diode on the control board prevents battery discharge.

Controls

• The GTO control board can be programmed for pull-to-open or push-to-open.

• Adjustable auto close, obstruction sensitivity and dual gate sequencing.

• Slow Start/Stop for added cycles and system life.

• Auto-memorization of digital transmitter code.

• Charging regulated circuit on control board. "Sleep draw" is 40 mA; "active draw" is 2 to 7 amps.

• GTO remote-mounted RF receiver tuned at 318 MHz.

Includes:

• Operator arm

• AC transformer

• 12 volt battery

• Control box/control board

• Receiver with 10 ft. cable

• Entry transmitter

• 6 ft. power cable

• Mounting hardware

• Installation/safety manual

• Caution signs.

• Warning Beeper

• Adjustable obstacle-reversing safety feature

$535.00  (plus $12.00 S&H)

 

or call toll-free to order at (877) 275-1270

GTO Slave Operator for PRO2500 only

Add this unit to the PRO2500 above and your system will operate a double swing gate up to 32' wide (16' each leaf). Burying the power cable directly across the driveway is fine. It can be snaked through conduit also. Cable is 1/4 inch diameter with a 1 inch plug on one end only.

Includes:

• Operator arm

• 40' power cable - wires into the control box of the PRO2500

• Mounting hardware

This operator will not work as a stand-alone unit. It is a slave unit without a control box and is meant to hook up to the PRO2500 control box for use with a double gate.

$285.00  (plus $12.00 S&H)

 

order by phone (1.877.275.1270) or online through our secure encrypted checkout system.